7643A REV A Norge Dryer Parts List

Evaporator fan motor (motor ac/dc evap fan)

This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.

Igniter kit (ignitor)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Bake element - push on terminals - 240v (bake element)

The bake element is located on the bottom of the oven with male spade terminals and push-on terminals. The bake element provides heat for baking. If your oven is too hot, not heating evenly, element is not heating, or little to no heat when baking, you may need to replace your bake element. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

Drawer slide rail - left side (slide asm lh)

When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. This part includes the rail only.

Shelf retainer bar end cap

The door shelf retainer bar end cap helps keep the retainer shelf bar in place to hold items on the door shelves. The end cap can be used for the left or right side of the door. This door end cap is almost two inches long, white in color, made entirely of plastic, and sold individually. This is a genuine OEM part.

Lower wheel assembly (wheel assembly (lwr))

The rack wheel and axle attach to the lower rack to allow you to slide the rack in and out easily. If your dish rack is not moving in and out of the dishwasher properly, you may have a broken or missing wheel and it will need to be replaced. The wheel and axle are white in color, made of plastic, and sold individually. This is a genuine OEM part kit.

Mounting bracket (bracket, undercounter)

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.

Dishwasher dishrack rollers and axles (roller slide)

This is a kit of 4 and also includes 4 axles.

Temperature sensor (sensor temp)

The temperature sensor, also known as a thermistor, helps detect the temperature inside the refrigerator and sends the information to the control board. If your refrigerator is too warm or not cooling properly, you may need to replace the temperature sensor. This is a genuine OEM part. Please make sure to disconnect the power to the refrigerator before starting your repair.

Air filter

This is an air filter for your air conditioner. The filter needs to be replaced if it becomes clogged, preventing cold air from circulating in your home. It measures approximately 14 1/2-inch by 10-inch. The air filter is beige in color and is sold individually. The air filter helps eliminate dirt, dust, and other airborne particles from coming into your home. This is a genuine OEM part which is sold individually.

Idler pulley assembly

The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.

Dishwasher door gasket with strike - black (dishwasher door seal and strike kit)

This one-piece door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking, tears, or there are gaps in your gasket, you may need to replace the door gasket. This black door gasket is made of rubber, includes a new latch strike plate for the door latch, and is a genuine OEM part.

Bake element

This genuine OEM bake element has push-on terminal ends and provides heat while baking. If the bake element has arcing, is shorted out, the oven is not heating evenly, or little or no heat when baking, you may need to replace it. When replacing the bake element please make sure you disconnect the power to the range. Make sure you do not let the wires fall back through the rear of the oven. This element has been updated by the manufacturer. New installation screws are required and are sold separately.

Refrigerator ice and water filter (Whirlpool everydrop refrigerator water filter)

Retaining ring (sub 410233)

The retaining clip goes onto the end of the roller axle and holds the drum roller on to the axle. If the ring is broken or damaged, you will need to replace it. This is a genuine OEM part and is sold individually.